Please wait while the page loads...

How many miles can you drive with the check engine light?

The safest bet is to decipher the code and then plan your strategy accordingly. Since each check engine code has its own level of severity, it is difficult to predict how many miles you can drive with the warning light on. It could be anything from a bad sensor to plug wires needing to be replaced. If you check engine light is flashing, we recommend that you pull over and contact Crown Chrysler Dodge Jeep Ram Greensboro to help represent if your automobile is safe to drive in or if we recommend a tow truck.

Chrysler Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that microscopic light on your vehicle’s dashboard instantly illuminates, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also noted as the OBD (on-board computer diagnostic system) in your Chrysler. There are hundreds of unmistakable codes that your check engine light can embrace. While that sounds daunting, with a microscopic patience, tackling paramount diagnostics will give you conducive knowledge about your vehicle and will also allow that Check Engine Light to do what it is really supposed to do: be your guide. Unfortunately, evident and favorable vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of achievable OBD codes, there are also hundreds of achievable reasons for the light, including:

  • Emissions controls issues
  • Ignition system faults
  • O2 Sensor
  • Computer output circuit issues
  • Loose Gas Cap or Missing Gas Cap
  • Old Battery
  • Bad Spark Plugs
  • Fuel and air metering systems problems
  • Transmission issues

This is why it is tremendous for someone who does not have a lot of automotive knowledge to not assume what a code means. If the engine light comes on due to a hazardous concern, you risk bad your car additional by not repairing the issue right away. Call Crown Chrysler Dodge Jeep Ram Greensboro at 3368951348 today or schedule your check engine light service online today! When your check engine light comes on, you should get it checked out quickly by a certified mechanic.

Chrysler Check Engine Light Flashing

Although there are plentiful potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are plentiful familiar causes including something as classic as a loose gas cap. Further familiar reasons for a Check Engine Light are damaged oxygen sensor, a malfunction with the fuel injection system, dirty mass airflow sensor, faulty emissions control part, faulty head gasket, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Certified Technicians and the certified service protocol to isolate the root problem and repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your issue was fixed.

Every Chrysler was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its critical systems. The sensors are continually detecting conditions while sending data to the electronic control squad. If the electronic control squad detects that the data is out of factory specifications, the Check Engine Light brightens telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is unsound nor what to do about it. That’s where we come in; Crown Chrysler Dodge Jeep Ram Greensboro provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Immensely Qualified Service professional.

Is it safe to drive your Chrysler with the check engine light on?

If the check engine light is shining, this means that there is a risky issue and it is recommended to service your Chrysler promptly. This question is not incredibly pragmatic because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to travel to work. This is naturally indicated by a steady glow of the check engine light. If you notice a difference in the performance of the automobile, it could be an indication of a more alarming problem. Call the advisors at Crown Chrysler Dodge Jeep Ram Greensboro by dialing 3368951348 so you can describe the issues. Or reduce your speed and transport your to our certified mechanics as soon as correct.

What Does the Check Engine Light Mean?

One of the most commonly misunderstood lights or indicators in your Chrysler is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few exact ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a assortment of things for your Chrysler. Some of these include ignition timing, controlling engine speed, shifting automatic transmissions and implementing stability control, just to name a few. With that being said, the check engine light can hint a mixture of alternative things. It can be as simple as your gas cap being loose or as relentless as engine knocking. If your check engine light is on in your Chrysler, contact Crown Chrysler Dodge Jeep Ram Greensboro. Our service department can help you find out what code is turning your check engine light on or audit why your check engine light is flashing. Contact Crown Chrysler Dodge Jeep Ram Greensboro today!

Will the check engine light reset itself?

The check engine light on your Chrysler will normally shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going careful, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your Chrysler light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to transport it in to Crown Chrysler Dodge Jeep Ram Greensboro so the light and code can be double-checked and reset.

Check Engine Light Service Chrysler

What do you do when you’re driving along in your Chrysler and instantly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your Chrysler checked as soon as probable. Ignoring that warning could end up causing first-rate damage to expensive engine factors.

When your Chrysler's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t honest, a computer turns on your check engine light. This amber or yellow light is mostly labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our auto repair mechanics at Crown Chrysler Dodge Jeep Ram Greensboro. There are also a number of relatively cheap code readers that are designed for do-it-yourselfers, should you opt for that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the issue and repair it.

What could cause the check engine light to come on in a Chrysler?

When your check engine light comes on, this could be as easy as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a alarming problem that could cause alarming damage to your engine and come with a unusual repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow constantly means something less alarming but a twinkling check engine light indicates that your vehicle’s engine is in alarming trouble and service is decisive at this moment. If your check engine light is twinkling in your Chrysler, we highly recommend not to drive the car and schedule service today. Below is a list of the most sufficient reasons your check engine light can come on:

  • Your Chrysler has a vacuum leak. Every Chrysler has a vacuum system that performs a dominant variety of functions. The vacuum system also helps lower intrusive emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, particularly if they’re exposed to imposing heat or extreme bitter.
  • Your mass airflow sensor (known as MAF) needs to be interchanged. The mass airflow sensor in your Chrysler is what determines how much fuel is crucial to run your engine efficiently by measuring the payment of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to definitive changes, like altitude. If your Chrysler is having trouble starting, idling rough or has a hasty change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • The battery is low or dead. The battery in your Chrysler is every awesome. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't actually require maintenance. The price of a new one depends on the type of you drive, but check our classic service coupons and specials.
  • One of the most commonplace and innumerable cause is that your Chrysler gas cap is loose, damaged or missing. The gas cap for your Chrysler serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is common or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on suddenly after you put gas in your Chrysler, first thing you should check is to make positive the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • New Spark Plugs or Plug Wires are crucial for your Chrysler. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or common, you will experience meager performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, large to more expensive repairs.
  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your Chrysler’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is ordinarily caused by neglected maintenance, which is why Crown Chrysler Dodge Jeep Ram Greensboro offers a complimentary multi-point inspection with every service. If you have an issue with your catalytic converter and don't get it repaired, your Chrysler will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause added problems from overheating.
  • Your O2 Sensor (Oxygen Sensor) needs to be interchanged. The Oxygen sensor, known as the O2 sensor, measures the payment of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less accessible when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your Chrysler's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to designate the right mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or added item can wreak havoc on your Chrysler if it’s not installed properly. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound commonplace, bring your Chrysler to and have our company of certified technicians ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, particularly aftermarket parts and accessories, or using OEM parts first place might cost a little bit more but could save you money from having to get meager work and damage caused by meager installation work corrected.

Chrysler Check Engine Light

A blinking light indicates that the problem is critical and if not taken care of immediately may result in main wear and tear to the vehicle. If the check engine light in your Chrysler starts blinking, that means that the problem needs brisk attention and your should be brought in immediately. This blinking light usually implies a exacting engine misfire allowing unburned fuel to be discarded into the exhaust system. There it can quickly boost the temperature of the catalytic converter to a point where damage is functional, requiring an lavish repair. Some owners ask if spark plugs cause the check engine light to flash? This can specifically be the cause. A bad, traditional or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our team of automotive specialists at Crown Chrysler Dodge Jeep Ram Greensboro quickly by calling 3368951348. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a incredibly expensive repair.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not perfectly tightened to a more risky failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it conducive to get the correct code reading and diagnosis. The average price for a check engine light diagnosis & testing is frequently between $88 and $111. The conducive news, Crown Chrysler Dodge Jeep Ram Greensboro offers complimentary multi-point inspections and free diagnostics, in most cases, to help mean the cause of your check engine light.